Manual Pages for UNIX Operating System command usage for man sane-pint

SANE Scanner Access Now Easy                         sane-pint(5)



NAME
     sane-pint - SANE backend for scanners that use the PINT dev-
     ice driver

DESCRIPTION
     The sane-pint library implements a SANE (Scanner Access  Now
     Easy)  backend that provides generic access to hand-held and
     flatbed scanners using the PINT (PINT Is Not  Twain)  device
     driver.   The PINT driver is being actively developed on the
     OpenBSD platform, and has been ported to a few  other  *nix-
     like operating systems.

     PINT is designed to provide an ioctl(2)  interface  to  many
     different  scanner  types.   However,  this backend has only
     been tested with flatbed single-pass scanners, and more work
     will  probably  be  required  to get it to use other scanner
     types successfully.

     If have successfully used the PINT driver with your scanner,
     but  it does not work using this SANE backend, please let us
     know.  To do this, send a mail with the relevant information
     for   your  scanner  to  sane-devel@lists.alioth.debian.org.
     Have   a   look   at    http://www.sane-project.org/mailing-
     lists.html concerning subscription to sane-devel.


DEVICE NAMES
     This backend expects device names of the form:

          special

     Where special is the UNIX path-name for the  special  device
     that  corresponds  to  the scanner.  The special device name
     must be a PINT device or a symlink to such  a  device.   For
     example,  under  NetBSD or OpenBSD, such a device name could
     be /dev/ss0 or /dev/scan0.

CONFIGURATION
     The contents of the pint.conf.  file is  a  list  of  device
     names  that  correspond  to  PINT scanners.  Empty lines and
     lines starting with a hash mark (#) are ignored.   A  sample
     configuration file is shown below:

          /dev/scanner
          # this is a comment
          /dev/ss1

FILES
     /etc/sane.d/pint.conf
          The backend configuration file (see also description of
          SANE_CONFIG_DIR below).




sane-backends 1.0.19Last change: 13 May 1998                    1






SANE Scanner Access Now Easy                         sane-pint(5)



     /usr/lib/sane/libsane-pint.a
          The static library implementing this backend.

     /usr/lib/sane/libsane-pint.so
          The shared library implementing this  backend  (present
          on systems that support dynamic loading).

ENVIRONMENT
     SANE_CONFIG_DIR
          This environment variable specifies the list of  direc-
          tories  that may contain the configuration file.  Under
          UNIX, the directories are separated by a  colon  (`:'),
          under  OS/2,  they are separated by a semi-colon (`;').
          If this variable is not set, the configuration file  is
          searched in two default directories: first, the current
          working directory (".") and then  in  /etc/sane.d.   If
          the  value  of  the  environment variable ends with the
          directory separator character, then the default  direc-
          tories  are  searched  after  the  explicitly specified
          directories.  For example, setting  SANE_CONFIG_DIR  to
          "/tmp/config:"     would    result    in    directories
          "tmp/config", ".", and "/etc/sane.d" being searched (in
          this order).

     SANE_DEBUG_PINT
          If the library was compiled with debug support enabled,
          this  environment variable controls the debug level for
          this backend.  E.g., a value of 128 requests all  debug
          output to be printed.  Smaller levels reduce verbosity.

SEE ALSO
     sane(7)

AUTHOR
     Gordon Matzigkeit, adapted from existing backends written by
     David Mosberger.

BUGS
     There are minor roundoff errors when adjusting  the  ranges,
     since  PINT  uses  units of 1/1200 of an inch, and SANE nor-
     mally uses millimeters.  Symptoms of these errors are skewed
     images.   This  should  really be fixed (no pun intended) as
     soon as possible, but I just don't  know/care  enough  about
     fixed-point  representation  and  roundoff errors to do this
     correctly.  Workaround: use inches as the scanning unit, and
     everything usually works fine.

     The PINT 0.5e interface does not provide a way to  determine
     valid  ranges  for DPI, modes, and scan sizes.  So, the SANE
     backend queries the PINT device, and  dynamically  discovers
     valid  ranges by doing a binary search.  This means that the
     driver takes longer to initialize than seems necessary.



sane-backends 1.0.19Last change: 13 May 1998                    2






SANE Scanner Access Now Easy                         sane-pint(5)



     Resetting the scanner does not seem to work (at least not on
     my  HP  ScanJet  4p).   For  that reason, the driver sends a
     SCIOCRESTART, then gobbles up any remaining input  until  it
     hits EOF.

     Not all of the scanners have been identified  (i.e.  whether
     they are flatbed or handheld).

     X and Y resolutions are assumed to be the same.

     No testing has been done on three-pass or handheld scanners,
     or with Automatic Document Feeder support.

ATTRIBUTES
     See attributes(5) for descriptions of the  following  attri-
     butes:

     _________________________________________________________
    |   ATTRIBUTE TYPE   |           ATTRIBUTE VALUE         |
    |____________________|____________________________________|_
    | Availability       |  image/scanner/xsane/sane-backends|
    |____________________|____________________________________|_
    | Interface Stability|  Uncommitted                      |
    |____________________|___________________________________|

NOTES
     Source for SANE is available on http://opensolaris.org.




























sane-backends 1.0.19Last change: 13 May 1998                    3