Manual Pages for UNIX Operating System command usage for man lset

Tcl Built-In Commands                                    lset(1T)



_________________________________________________________________

NAME
     lset - Change an element in a list

SYNOPSIS
     lset varName ?index...? newValue
_________________________________________________________________

DESCRIPTION
     The lset command accepts  a  parameter,  varName,  which  it
     interprets  as the name of a variable containing a Tcl list.
     It also accepts zero or more indices  into  the  list.   The
     indices may be presented either consecutively on the command
     line, or grouped in a Tcl list and  presented  as  a  single
     argument.  Finally, it accepts a new value for an element of
     varName.

     If no indices are presented, the command takes the form:
          lset varName newValue
     or
          lset varName {} newValue
     In this case, newValue replaces the old value of  the  vari-
     able varName.

     When presented with a single index, the lset command  treats
     the  content  of  the  varName  variable  as a Tcl list.  It
     addresses the index'th element in it (0 refers to the  first
     element  of  the  list).   When  interpreting the list, lset
     observes the same rules concerning  braces  and  quotes  and
     backslashes  as  the Tcl command interpreter; however, vari-
     able substitution and command  substitution  do  not  occur.
     The  command  constructs  a new list in which the designated
     element is replaced with newValue.  This new list is  stored
     in  the  variable varName, and is also the return value from
     the lset command.

     If index is negative or greater than or equal to the  number
     of elements in $varName, then an error occurs.

     If index has the value end, it refers to the last element in
     the  list, and end-integer refers to the last element in the
     list minus the specified integer offset.

     If additional index arguments are supplied, then each  argu-
     ment  is used in turn to address an element within a sublist
     designated by the previous indexing operation, allowing  the
     script to alter elements in sublists.  The command,
          lset a 1 2 newValue
     or
          lset a {1 2} newValue
     replaces element 2 of sublist 1 with newValue.



Tcl                     Last change: 8.4                        1






Tcl Built-In Commands                                    lset(1T)



     The integer appearing in each index argument must be greater
     than  or equal to zero.  The integer appearing in each index
     argument must be  strictly  less  than  the  length  of  the
     corresponding list.  In other words, the lset command cannot
     change the size of a list.  If an index is outside the  per-
     mitted range, an error is reported.

EXAMPLES
     In each of these examples, the initial value of x is:
          set x [list [list a b c] [list d e f] [list g h i]]
            => {a b c} {d e f} {g h i}
     The indicated return value also becomes the new value  of  x
     (except in the last case, which is an error which leaves the
     value of x unchanged.)
          lset x {j k l} => j k l
          lset x {} {j k l} => j k l
          lset x 0 j => j {d e f} {g h i}
          lset x 2 j => {a b c} {d e f} j
          lset x end j => {a b c} {d e f} j
          lset x end-1 j => {a b c} j {g h i}
          lset x 2 1 j => {a b c} {d e f} {g j i}
          lset x {2 1} j => {a b c} {d e f} {g j i}
          lset x {2 3} j => list index out of range
     In the following examples, the initial value of x is:
          set x [list [list [list a b] [list c d]] \
                      [list [list e f] [list g h]]]
           => {{a b} {c d}} {{e f} {g h}}
     The indicated return value also becomes the new value of x.
          lset x 1 1 0 j => {{a b} {c d}} {{e f} {j h}}
          lset x {1 1 0} j => {{a b} {c d}} {{e f} {j h}}

SEE ALSO
     list(1T), lappend(1T), lindex(1T), linsert(1T), llength(1T),
     lsearch(1T), lsort(1T), lrange(1T), lreplace(1T)


KEYWORDS
     element, index, list, replace, set

ATTRIBUTES
     See attributes(5) for descriptions of the  following  attri-
     butes:













Tcl                     Last change: 8.4                        2






Tcl Built-In Commands                                    lset(1T)



     _______________________________________
    |   ATTRIBUTE TYPE   |  ATTRIBUTE VALUE|
    |____________________|__________________|_
    | Availability       |  runtime/tcl-8  |
    |____________________|__________________|_
    | Interface Stability|  Uncommitted    |
    |____________________|_________________|

NOTES
     Source for Tcl is available on http://opensolaris.org.













































Tcl                     Last change: 8.4                        3