Windows PowerShell command on Get-command fcinfo

Manual Pages for UNIX Operating System command usage for man fcinfo

System Administration Commands fcinfo(1M)

NAME

fcinfo, fcadm - Fibre Channel HBA Port Command Line Inter-

face

SYNOPSIS

fcinfo hba-port [-lite] [HBA_port_WWN]...

fcadm hba-port [-lite] [HBA_port_WWN]...

fcinfo remote-port [-ls] [-p HBA_port_WWN]

[REMOTE_port_WWN]...

fcadm remote-port [-ls] [-p HBA_port_WWN]

[REMOTE_port_WWN]...

fcinfo logical-unit | lu [-v] [OS device_path]

fcadm logical-unit | lu [-v] [OS device_path]

fcadm create-npiv-port -p Virtual_Port_WWN [-n Virtual_Node_WWN]

PhysicalPort_port_WWN

fcadm delete-npiv-port -p Virtual_Port_WWN [-n Virtual_Node_WWN]

PhysicalPort_port_WWN

fcadm create-fcoe-port [-tf] -p Port_WWN [-n Node_WWN]

MAC_Interface

fcadm delete-fcoe-port MAC_Interface

fcadm list-fcoe-ports MAC_Interface

fcadm force-lip Port_WWN

fcinfo [-V]

fcadm [-V]

SunOS 5.11 Last change: 26 Jul 2009 1

System Administration Commands fcinfo(1M)

fcinfo [-?]

fcadm [-?]

DESCRIPTION

fcinfo and fcadm are command line interfaces that collect

administrative information on fibre channel host bus adapter (HBA) ports on a host. They also collect data on any fibre channel targets that might be connected to those ports in a Storage Area Network (SAN). A port can be either in initiator mode or target mode. The same FC attribute information and remote port information are applied to both the initiator and the target modes port

except that SCSI-related operations described below do not

apply for the target mode port. SUBCOMMANDS

The following subcommands are supported by both fcinfo and

fcadm:

hba-port Lists information for the HBA port

referenced by the specified

HBA_port_WWN. If HBA_port_WWN is not

specified, all initiator mode and tar-

get mode fibre channel HBA ports on the host will be listed.

remote-port Lists the remote-port information for

those remote ports that are specified.

If no REMOTE_port_WWN is specified, all

remote ports that are visible through

HBA_port_WWN are listed.

logical-unit | lu Lists the logical unit referenced by

the specified device_path. If

device_path is not specified, all fibre

channel logical units will be listed. This subcommand applies only to the initiator mode.

The following subcommands, which administer N_Port ID Virtu-

alization (NPIV) HBA ports, are supported only by fcadm:

SunOS 5.11 Last change: 26 Jul 2009 2

System Administration Commands fcinfo(1M)

create-npiv-port

Create an NPIV virtual port on the specified adapter.

delete-npiv-port

Delete an NPIV virtual port. This delete only ports create by fcadm. The following subcommands, which administer Fibre Channel over Ethernet (FCoE) ports, are supported only by fcadm:

create-fcoe-port

Creates a FCoE port associated with the given MAC inter-

face and the given Port_WWN/Node_WWN. If -p or -n is not

specified, the Port WWN or Node WWN will be generated automatically. If the specified MAC interface does not support multiple unicast address, no FCoE port will be created and you receive a message indicating that you

can add an -f option to force enabling promiscuous mode

on the specified MAC interface to enable FCoE.

delete-fcoe-port

Deletes the FCoE port associated with the specified MAC interface.

list-fcoe-ports

List information of FCoE ports.

force-lip

Force the link to reinitialize. When issuing this sub-

command on the target port side, causes a reset of the target port. When issuing it from the host port side, resets the host port. When an FC switch is connected, other FC ports in the SAN will get a RSCN (Remote State Change Notification). Furthermore, other initiators will always rediscover the port after this, and the FC

will be continued. This command is disruptive to I/Os, but it is not destructive, as it does not cause any data loss.

SunOS 5.11 Last change: 26 Jul 2009 3

System Administration Commands fcinfo(1M)

OPTIONS The following options are supported:

-e, --fcoe

Lists the information for all FCoE ports.

-f, --fcoe-promiscuous

Used with create-fcoe-port to create an FCoE port on a

MAC interface associated with a NIC that does not sup-

port multiple unicast address. Promiscuous mode will be enabled for the specified MAC interface.

-l, --linkstat

Lists the link error statistics information for the port

referenced by the specified HBA_port_WWN or

REMOTE_port_WWN.

-n HBA_node_WWN, --node HBA_node_WWN

When used with NPIV options, specify a virtual node WWN.

If used with create-npiv-port, it can be omitted, and a

random based WWN will be used. It is mandatory for

delete-npiv-port.

When used with create-fcoe-port subcommand, specify the

node WWN for the FCoE port. It can be omitted, in which case a WWN will be generated based on the MAC address of the specified MAC interface.

-p HBA_port_WWN, --port HBA_port_WWN

Retrieve remote port information from the HBA_port_WWN

of the local HBA port on the host. When used with the

remote-port subcommand, the -p option is mandatory.

When used with NPIV options, specify a virtual port WWN.

If used with create-npiv-port, it can be omitted, and a

random based WWN will be used. It is mandatory for

delete-npiv-port.

When used with create-fcoe-port subcommand, specify the

port WWN for the FCoE port. It can be omitted, in which case a WWN will be generated based on the MAC address of the specified MAC interface.

SunOS 5.11 Last change: 26 Jul 2009 4

System Administration Commands fcinfo(1M)

-s, --scsi-target

Lists the SCSI target information for all remote ports

the user has asked for. The -p, --port option must

always be specified and must be a valid HBA port on the host. This HBA port will be used as the initiator for which to retrieve the SCSI level target information. Note that this will only function on remote port fibre

channel World-Wide Names that support an FC4 type of

SCSI. This option applies only to an initiator mode port.

-t [HBA_node_WWN], -target [HBA_node_WWN]

Lists the information for the port with the target mode

referenced by the specified HBA_node_WWN or all target

mode ports discovered in the host.

When used with create-fcoe-port, create a FCoE target

mode port.

-v, --verbose

When used with the logical-unit subcommand, the -v

displays additional information for the logical unit, including SCSI vendor and product information and device

type as well as the FC World-Wide names for the local

and remote fibre channel ports to which this device is attached.

-V, --version

Displays the version information.

-?, --help

Displays the usage information.

EXAMPLES

Example 1 Listing All HBA Ports The following command lists all initiator mode fibre channel HBA ports on the host:

# fcinfo hba-port

SunOS 5.11 Last change: 26 Jul 2009 5

System Administration Commands fcinfo(1M)

HBA Port WWN: 210000e08b074cb5 Port Mode: Initiator OS Device Name: /dev/cfg/c1 Manufacturer: QLogic Corp.

Model: 375-3108-xx

Firmware Version: 3.3.116

FCode/BIOS Version: 1.13.08 Serial Number: not available Driver Name: qlc

Driver Version: 20070212-2.19

Type: N-port

State: online Supported Speeds: 1Gb 2Gb Current Speed: 2Gb Node WWN: 200000e08b074cb5 NPIV Port List: Virtual Port 1: Port WWN: 200000e08b074cb1 Node WWN: 200000e08b074cb3 HBA Port WWN: 210100e08b274cb5 Port Mode: Initiator OS Device Name: /dev/cfg/c2 Manufacturer: QLogic Corp.

Model: 375-3108-xx

Firmware Version: 3.3.116

FCode/BIOS Version: 1.13.08 Serial Number: not available Driver Name: qlc

Driver Version: 20070212-2.19

Type: N-port

State: online Supported Speeds: 1Gb 2Gb Current Speed: 2Gb Node WWN: 200100e08b274cb5 HBA Port WWN: 210000e08b072ab5 Port Mode: Initiator OS Device Name: /dev/cfg/c3 Manufacturer: QLogic Corp. Firmware Version: 3.3.116

FCode/BIOS Version: 1.13.08

Model: 375-3108-xx

Serial Number: not available Driver Name: qlc

Driver Version: 20070212-2.19

Type: L-port

State: online Supported Speeds: 1Gb 2Gb Current Speed: 2Gb Node WWN: 200000e08b072ab5 HBA Port WWN: 210100e08b272ab5 Port Mode: Initiator OS Device Name: /dev/cfg/c4

SunOS 5.11 Last change: 26 Jul 2009 6

System Administration Commands fcinfo(1M)

Manufacturer: QLogic Corp.

Model: 375-3108-xx

Firmware Version: 3.3.116

FCode/BIOS Version: 1.13.08

Serial Number: 0402F00-0549112808

Driver Name: qlc

Driver Version: 20070212-2.19

Type: N-port

State: online Supported Speeds: 1Gb 2Gb Current Speed: 2Gb Node WWN: 200100e08b272ab5 Example 2 Listing Target Mode HBA Ports The following command lists all target mode fibre channel HBA ports on the host:

# fcinfo hba-port -t

HBA Port WWN: 210100e08bb09221 Port Mode: Target Port ID: 10700 OS Device Name: Not Applicable Manufacturer: QLogic Corp. Model: d30ac7e0 Firmware Version: 4.0.109

FCode/BIOS Version: N/A

Type: F-port

State: online Supported Speeds: not established Current Speed: 2Gb Node WWN: 200100e08bb09221 HBA Port WWN: 210000e08b909221 Port Mode: Target Port ID: 10900 OS Device Name: Not Applicable Manufacturer: QLogic Corp. Model: d37ad1e0 Firmware Version: 4.0.109

FCode/BIOS Version: N/A

Type: F-port

State: online Supported Speeds: not established Current Speed: 2Gb Node WWN: 200000e08b909221 HBA Port WWN: 200000144fc2d508 Port Mode: Target Port ID: 9a0025

SunOS 5.11 Last change: 26 Jul 2009 7

System Administration Commands fcinfo(1M)

OS Device Name: Not Applicable Manufacturer: Sun Microsystems, Inc. Model: FCoE Virtual FC HBA

Firmware Version: N/A

FCode/BIOS Version: N/A

Serial Number: N/A Driver Name: COMSTAR FCOET Driver Version: 1.0

Type: F-port

State: online Supported Speeds: 1Gb 10Gb Current Speed: 10Gb Node WWN: 100000144fc2d508 HBA Port WWN: 200000144fc2d509 Port Mode: Target Port ID: 9a0023 OS Device Name: Not Applicable Manufacturer: Sun Microsystems, Inc. Model: FCoE Virtual FC HBA

Firmware Version: N/A

FCode/BIOS Version: N/A

Serial Number: N/A Driver Name: COMSTAR FCOET Driver Version: 1.0

Type: F-port

State: online Supported Speeds: 1Gb 10Gb Current Speed: 10Gb Node WWN: 100000144fc2d509 Example 3 Listing HBA Ports and Link Statistics The following command lists information for the HBA ports and the link statistics for those ports:

# fcinfo hba-port -l 210000e08b074cb5 210100e08b274cb5

HBA Port WWN: 210000e08b074cb5 Port Mode: Initiator OS Device Name: /dev/cfg/c1 Manufacturer: QLogic Corp.

Model: 375-3108-xx

Firmware Version: 3.3.116

FCode/BIOS Version: 1.13.08

Serial Number: 0402F00-0549112808

Driver Name: qlc

Driver Version: 20070212-2.19

Type: N-port

SunOS 5.11 Last change: 26 Jul 2009 8

System Administration Commands fcinfo(1M)

State: online Supported Speeds: 1Gb 2Gb Current Speed: 2Gb Node WWN: 200000e08b074cb5 Link Error Statistics: Link Failure Count: 0 Loss of Sync Count: 0 Loss of Signal Count: 0 Primitive Seq Protocol Error Count: 0 Invalid Tx Word Count: 0 Invalid CRC Count: 0 HBA Port WWN: 210100e08b274cb5 Port Mode: Initiator OS Device Name: /dev/cfg/c2 Manufacturer: QLogic Corp.

Model: 375-3108-xx

Firmware Version: 3.3.116

FCode/BIOS Version: 1.13.08

Serial Number: 0402F00-0549112808

Driver Name: qlc

Driver Version: 20070212-2.19

Type: N-port

State: online Supported Speeds: 1Gb 2Gb Current Speed: 2Gb Node WWN: 200100e08b274cb5 Link Error Statistics: Link Failure Count: 0 Loss of Sync Count: 0 Loss of Signal Count: 0 Primitive Seq Protocol Error Count: 0 Invalid Tx Word Count: 0 Invalid CRC Count: 0 Example 4 Listing All Remote Ports

The following command lists all remote ports that are visi-

ble through the given HBA port:

# fcinfo remote-port -p 210100e08b274cb5

Remote Port WWN: 50020f230000b4af Active FC4 Types: SCSI SCSI Target: yes Port Symbolic Name: unknown Node WWN: 50020f200000b4af Remote Port WWN: 210000e08b07daa6 Active FC4 Types: SCSI

SunOS 5.11 Last change: 26 Jul 2009 9

System Administration Commands fcinfo(1M)

SCSI Target: no Port Symbolic Name: unknown Node WWN: 200000e08b07daa6 Remote Port WWN: 20030003ba27c788 Active FC4 Types: SCSI SCSI Target: yes Port Symbolic Name: unknown Node WWN: 10000003ba27c788 Remote Port WWN: 210000e08b096a60 Active FC4 Types: SCSI,IP SCSI Target: no Port Symbolic Name: unknown Node WWN: 200000e08b096a60 Example 5 Listing Remote Ports and Link Statistics The following command lists information for the remote ports and the link statistics for those ports:

# fcinfo remote-port -l -p 210100e08b272ab5

Remote Port WWN: 210100e08b296a60 Active FC4 Types: SCSI,IP SCSI Target: no Port Symbolic Name: unknown Node WWN: 200100e08b296a60 Link Error Statistics: Link Failure Count: 0 Loss of Sync Count: 0 Loss of Signal Count: 0 Primitive Seq Protocol Error Count: 0 Invalid Tx Word Count: 0 Invalid CRC Count: 0 Remote Port WWN: 20030003ba27d56d Active FC4 Types: SCSI SCSI Target: yes Port Symbolic Name: unknown Node WWN: 10000003ba27d56d Link Error Statistics: Link Failure Count: 0 Loss of Sync Count: 4765165 Loss of Signal Count: 4765165 Primitive Seq Protocol Error Count: 0 Invalid Tx Word Count: 0 Invalid CRC Count: 0 Remote Port WWN: 210100e08b27f7a6 Active FC4 Types: SCSI SCSI Target: no

SunOS 5.11 Last change: 26 Jul 2009 10

System Administration Commands fcinfo(1M)

Port Symbolic Name: unknown Node WWN: 200100e08b27f7a6 Link Error Statistics: Link Failure Count: 0 Loss of Sync Count: 0 Loss of Signal Count: 0 Primitive Seq Protocol Error Count: 0 Invalid Tx Word Count: 0 Invalid CRC Count: 0 Remote Port WWN: 50020f230000b897 Active FC4 Types: SCSI SCSI Target: yes Port Symbolic Name: unknown Node WWN: 50020f200000b897 Link Error Statistics: Link Failure Count: 0 Loss of Sync Count: 7 Loss of Signal Count: 7 Primitive Seq Protocol Error Count: 0 Invalid Tx Word Count: 0 Invalid CRC Count: 0 Remote Port WWN: 210100e08b27daa6 Active FC4 Types: SCSI SCSI Target: no Port Symbolic Name: unknown Node WWN: 200100e08b27daa6 Link Error Statistics: Link Failure Count: 0 Loss of Sync Count: 0 Loss of Signal Count: 0 Primitive Seq Protocol Error Count: 0 Invalid Tx Word Count: 0 Invalid CRC Count: 0 Remote Port WWN: 210000e08b074cb5 Active FC4 Types: SCSI,IP SCSI Target: no Port Symbolic Name: unknown Node WWN: 200000e08b074cb5 Link Error Statistics: Link Failure Count: 0 Loss of Sync Count: 0 Loss of Signal Count: 0 Primitive Seq Protocol Error Count: 0 Invalid Tx Word Count: 0 Invalid CRC Count: 0 Remote Port WWN: 210100e08b296060 Active FC4 Types: SCSI SCSI Target: no Port Symbolic Name: unknown Node WWN: 200100e08b296060 Link Error Statistics: Link Failure Count: 0

SunOS 5.11 Last change: 26 Jul 2009 11

System Administration Commands fcinfo(1M)

Loss of Sync Count: 0 Loss of Signal Count: 0 Primitive Seq Protocol Error Count: 0 Invalid Tx Word Count: 0 Invalid CRC Count: 0 Example 6 Listing All SCSI Targets and Link Statistics The following command lists all remote ports as well as the

link statistics and scsi-target information:

# fcinfo remote-port -sl -p 210100e08b272ab5

Remote Port WWN: 210100e08b296a60 Active FC4 Types: SCSI,IP SCSI Target: no Port Symbolic Name: unknown Node WWN: 200100e08b296a60 Link Error Statistics: Link Failure Count: 0 Loss of Sync Count: 0 Loss of Signal Count: 0 Primitive Seq Protocol Error Count: 0 Invalid Tx Word Count: 0 Invalid CRC Count: 0 Remote Port WWN: 20030003ba27d56d Active FC4 Types: SCSI SCSI Target: yes Port Symbolic Name: unknown Node WWN: 10000003ba27d56d Link Error Statistics: Link Failure Count: 0 Loss of Sync Count: 4765165 Loss of Signal Count: 4765165 Primitive Seq Protocol Error Count: 0 Invalid Tx Word Count: 0 Invalid CRC Count: 0 LUN: 0 Vendor: SUN Product: T4 OS Device Name: /dev/rdsk/c4t20030003BA27D56Dd0s2 LUN: 1 Vendor: SUN Product: T4 OS Device Name: /dev/rdsk/c4t20030003BA27D56Dd1s2 Remote Port WWN: 210100e08b27f7a6 Active FC4 Types: SCSI SCSI Target: no

SunOS 5.11 Last change: 26 Jul 2009 12

System Administration Commands fcinfo(1M)

Port Symbolic Name: unknown Node WWN: 200100e08b27f7a6 Link Error Statistics: Link Failure Count: 0 Loss of Sync Count: 0 Loss of Signal Count: 0 Primitive Seq Protocol Error Count: 0 Invalid Tx Word Count: 0 Invalid CRC Count: 0 Remote Port WWN: 50020f230000b897 Active FC4 Types: SCSI SCSI Target: yes Port Symbolic Name: unknown Node WWN: 50020f200000b897 Link Error Statistics: Link Failure Count: 0 Loss of Sync Count: 7 Loss of Signal Count: 7 Primitive Seq Protocol Error Count: 0 Invalid Tx Word Count: 0 Invalid CRC Count: 0 LUN: 0 Vendor: SUN Product: T300 OS Device Name: Unknown LUN: 1 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d1s2 LUN: 2 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d2s2 LUN: 3 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d3s2 LUN: 4 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d4s2 LUN: 5 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d5s2 LUN: 6 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d6s2 LUN: 7 Vendor: SUN Product: T300

SunOS 5.11 Last change: 26 Jul 2009 13

System Administration Commands fcinfo(1M)

OS Device Name: /dev/rdsk/c4t50020F230000B897d7s2 LUN: 8 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d8s2 LUN: 9 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d9s2 LUN: 10 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d10s2 LUN: 11 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d11s2 LUN: 12 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d12s2 LUN: 13 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d13s2 LUN: 14 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d14s2 LUN: 15 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d15s2 Remote Port WWN: 210100e08b27daa6 Active FC4 Types: SCSI SCSI Target: no Port Symbolic Name: unknown Node WWN: 200100e08b27daa6 Link Error Statistics: Link Failure Count: 0 Loss of Sync Count: 0 Loss of Signal Count: 0 Primitive Seq Protocol Error Count: 0 Invalid Tx Word Count: 0 Invalid CRC Count: 0 Remote Port WWN: 210000e08b074cb5 Active FC4 Types: SCSI,IP SCSI Target: no Port Symbolic Name: unknown Node WWN: 200000e08b074cb5 Link Error Statistics: Link Failure Count: 0

SunOS 5.11 Last change: 26 Jul 2009 14

System Administration Commands fcinfo(1M)

Loss of Sync Count: 0 Loss of Signal Count: 0 Primitive Seq Protocol Error Count: 0 Invalid Tx Word Count: 0 Invalid CRC Count: 0 Remote Port WWN: 210100e08b296060 Active FC4 Types: SCSI SCSI Target: no Port Symbolic Name: unknown Node WWN: 200100e08b296060 Link Error Statistics: Link Failure Count: 0 Loss of Sync Count: 0 Loss of Signal Count: 0 Primitive Seq Protocol Error Count: 0 Invalid Tx Word Count: 0 Invalid CRC Count: 0 Example 7 Listing SCSI Target Information The following command lists all remote ports as well as the

scsi-target information:

# fcinfo remote-port -s -p 210100e08b272ab5

Remote Port WWN: 210100e08b296a60 Active FC4 Types: SCSI,IP SCSI Target: no Port Symbolic Name: unknown Node WWN: 200100e08b296060 Remote Port WWN: 20030003ba27d56d Active FC4 Types: SCSI SCSI Target: yes Port Symbolic Name: unknown Node WWN: 10000003ba27d56d LUN: 0 Vendor: SUN Product: T4 OS Device Name: /dev/rdsk/c4t20030003BA27D56Dd0s2 LUN: 1 Vendor: SUN Product: T4 OS Device Name: /dev/rdsk/c4t20030003BA27D56Dd1s2 Remote Port WWN: 210100e08b27f7a6 Active FC4 Types: SCSI SCSI Target: no Port Symbolic Name: unknown Node WWN: 200100e08b27f7a6

SunOS 5.11 Last change: 26 Jul 2009 15

System Administration Commands fcinfo(1M)

Remote Port WWN: 50020f230000b897 Active FC4 Types: SCSI SCSI Target: yes Port Symbolic Name: unknown Node WWN: 50020f200000b897 LUN: 0 Vendor: SUN Product: T300 OS Device Name: Unknown LUN: 1 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d1s2 LUN: 2 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d2s2 LUN: 3 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d3s2 LUN: 4 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d4s2 LUN: 5 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d5s2 LUN: 6 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d6s2 LUN: 7 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d7s2 LUN: 8 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d8s2 LUN: 9 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d9s2 LUN: 10 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d10s2 LUN: 11 Vendor: SUN Product: T300

SunOS 5.11 Last change: 26 Jul 2009 16

System Administration Commands fcinfo(1M)

OS Device Name: /dev/rdsk/c4t50020F230000B897d11s2 LUN: 12 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d12s2 LUN: 13 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d13s2 LUN: 14 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d14s2 LUN: 15 Vendor: SUN Product: T300 OS Device Name: /dev/rdsk/c4t50020F230000B897d15s2 Remote Port WWN: 210100e08b27daa6 Active FC4 Types: SCSI SCSI Target: no Port Symbolic Name: unknown Node WWN: 200100e08b27daa6 Remote Port WWN: 210000e08b074cb5 Active FC4 Types: SCSI,IP SCSI Target: no Port Symbolic Name: unknown Node WWN: 200000e08b074cb5 Remote Port WWN: 210100e08b296060 Active FC4 Types: SCSI SCSI Target: no Port Symbolic Name: unknown Node WWN: 200100e08b296060 Example 8 Listing the Logical Unit The following command lists the logical unit:

# fcinfo logical-unit

/dev/rdsk/c0t600C0FF0000000000036223AE73EB705d0s2 /dev/rdsk/c0t600C0FF00000000000362272539E5B03d0s2 /dev/rmt/0n Example 9 Displaying Additional Information for the Logical Unit

SunOS 5.11 Last change: 26 Jul 2009 17

System Administration Commands fcinfo(1M)

The following command displays additional information about

the logical unit using the -v option for device /dev/rmt/On:

# fcinfo lu -v /dev/rmt/On

OS Device Name: /dev/rmt/0n HBA Port WWN: 210000e07c030b91 Remote Port WWN: 21010003b7830a6 LUN: 0 Vendor: STK Product: 9940A Device Type: Tape device The following command displays additional information about

the logical unit using the -v option for device

/dev/rdsk/c0t600C0FF0000000000036223AE73EB705d0s2

# fcinfo logical-unit -v \

/dev/rdsk/c0t600C0FF0000000000036223AE73EB705d0s2 OS Device Name: /dev/rdsk/c0t600C0FF0000000000036223AE73EB705d0s2 HBA Port WWN: 210100e08b27a8a1 Remote Port WWN: 256000c0ffc03622 LUN: 0 Remote Port WWN: 216000c0ff803622 LUN: 0 HBA Port WWN: 210000e08b07a8a1 Remote Port WWN: 256000c0ffc03622 LUN: 0 Remote Port WWN: 216000c0ff803622 LUN: 0 Vendor: SUN Product: StorEdge 3510 Device Type: Disk device Example 10 Adding an NIPV Port The following command adds an NPIV port to the HBA with a port name: 210000e08b170f1c

SunOS 5.11 Last change: 26 Jul 2009 18

System Administration Commands fcinfo(1M)

The NPIV port has a port name of 2000000000000001 and a node name of 2100000000000001.

# fcadm create-npiv-port -p 2000000000000001 -n 2100000000000001 \

210000e08b170f1c Created NPIV Port: HBA Port WWN: 2000000000000001 Node WWN: 2100000000000001 Physical HBA Port WWN: 210000e08b170f1c Example 11 Adding an NIPV Port with Random WWN The following command adds an NPIV port to the HBA with a randomly assigned port name of 210000e08b170f1c.

# fcadm create-npiv-port 210000e08b170f1c

Created NPIV Port: HBA Port WWN: 2038295824942801 Node WWN: 2100392849248001 Physical HBA Port WWN: 210000e08b170f1c Example 12 Deleting an NIPV Port The following command deletes an NPIV port.

# fcadm delete-npiv-port -p 2000000000000001 -w 2100000000000001 \

210000e08b170f1c Example 13 Creating an FCoE Target Port The following command creates an FCoE port associated with the MAC interface nxge0.

# fcadm create-fcoe-port -t nxge0

SunOS 5.11 Last change: 26 Jul 2009 19

System Administration Commands fcinfo(1M)

Example 14 Deleting an FCoE Port The following command deletes the FCoE port associated with the MAC interface nxge0.

# fcadm delete-fcoe-port -t nxge0

Example 15 Listing Information for an FCoE Port The following command lists information for FCoE ports.

# fcadm list-fcoe-ports

HBA Port WWN: 200000144fc2d508 Port Type: Target MAC Name: nxge0 MTU Size: 9194 MAC Factory Address: 00144fc2d508 MAC Current Address: 00144fc2d508 HBA Port WWN: 200000144fc2d509 Port Type: Target MAC Name: nxge1 MTU Size: 9194 MAC Factory Address: 00144fc2d509 MAC Current Address: 00144fc2d509 Example 16 Reinitializing the Link of an FC Port The following command forces the link connected with the port 200000144fc2d508 to reinitialize.

# fcadm force-lip 200000144fc2d508

ATTRIBUTES

See attributes(5) for descriptions of the following attri-

butes:

SunOS 5.11 Last change: 26 Jul 2009 20

System Administration Commands fcinfo(1M)

____________________________________________________________

| ATTRIBUTE TYPE | ATTRIBUTE VALUE |

| ____________________________|_____________________________|_

| Availability | system/storage/fibre- |

| | channel/port-utility |

|_____________________________|_____________________________|

| Interface Stability | Committed |

|_____________________________|_____________________________|

ERROR MESSAGES

Errors that can occur in addition to the errors normally associated with system administration commands:

o HBA_port_WWN: not found

o Remote_port_WWN: not found

o HBA_port_WWN: NPIV not supported on this HBA

SunOS 5.11 Last change: 26 Jul 2009 21

Manual Pages for UNIX Operating System command usage for man fcinfo

System Administration Commands fcinfo(1M)

NAME

fcinfo, fcadm - Fibre Channel HBA Port Command Line Inter-

SYNOPSIS

fcinfo hba-port [-lite] [HBA_port_WWN]...

fcinfo remote-port [-ls] [-p HBA_port_WWN]

fcinfo logical-unit | lu [-v] [OS device_path]

fcinfo [-V]

System Administration Commands fcinfo(1M)

fcinfo [-?]

DESCRIPTION

fcinfo and fcadm are command line interfaces that collect

The following subcommands are supported by both fcinfo and

System Administration Commands fcinfo(1M)

System Administration Commands fcinfo(1M)

System Administration Commands fcinfo(1M)

EXAMPLES

# fcinfo hba-port

System Administration Commands fcinfo(1M)

System Administration Commands fcinfo(1M)

# fcinfo hba-port -t

System Administration Commands fcinfo(1M)

# fcinfo hba-port -l 210000e08b074cb5 210100e08b274cb5

System Administration Commands fcinfo(1M)

# fcinfo remote-port -p 210100e08b274cb5

System Administration Commands fcinfo(1M)

# fcinfo remote-port -l -p 210100e08b272ab5

System Administration Commands fcinfo(1M)

System Administration Commands fcinfo(1M)

# fcinfo remote-port -sl -p 210100e08b272ab5

System Administration Commands fcinfo(1M)

System Administration Commands fcinfo(1M)

System Administration Commands fcinfo(1M)

# fcinfo remote-port -s -p 210100e08b272ab5

System Administration Commands fcinfo(1M)

System Administration Commands fcinfo(1M)

# fcinfo logical-unit

System Administration Commands fcinfo(1M)

# fcinfo lu -v /dev/rmt/On

# fcinfo logical-unit -v \

System Administration Commands fcinfo(1M)

System Administration Commands fcinfo(1M)

ATTRIBUTES

System Administration Commands fcinfo(1M)

| ATTRIBUTE TYPE | ATTRIBUTE VALUE |

SEE ALSO

ERROR MESSAGES