NAME
firewall-offline-cmd - firewalld offline command line client
SYNOPSIS
firewall-offline-cmd [OPTIONS...]
DESCRIPTION
firewall-offline-cmd is an offline command line client of the firewalld
daemon. It should be used only if the firewalld service is not running.
For example to migrate from system-config-firewall/lokkit or in the
install environment to configure firewall settings with kickstart.
Some lokkit options can not be automatically converted for firewalld,
they will result in an error or warning message. This tool tries to
convert as much as possible, but there are limitations for example with
custom rules, modules and masquerading.
Check the firewall configuration after using this tool.
OPTIONS
If no options are given, configuration from
/etc/sysconfig/system-config-firewall will be migrated.
For sequence options, this are the options that can be specified
multiple times, the exit code is 0 if there is at least one item that
succeded. The ALREADYENABLED (11), NOTENABLED (12) and also
ZONEALREADYSET (16) errors are treated as succeeded. If there are
issues while parsing the items, then these are treated as warnings and
will not change the result as long as there is a succeeded one. Without
any succeeded item, the exit code will depend on the error codes. If
there is exactly one error code, then this is used. If there are more
than one then UNKNOWNERROR (254) will be used.
The following options are supported:
General Options
-h, help
Prints a short help text and exists.
-V, version
Prints the version string of firewalld and exits.
-q, quiet
Do not print status messages.
Status Options
enabled
Enable the firewall. This option is a default option and will
activate the firewall if not already enabled as long as the option
disabled is not given.
disabled
Disable the firewall by disabling the firewalld service.
Lokkit Compatibility Options
These options are nearly identical to the options of lokkit.
migrate-system-config-firewall=file
Migrate system-config-firewall configuration from the given file.
No further
addmodule=module
This option will result in a warning message and will be ignored.
Handling of netfilter helpers has been merged into services
completely. Adding or removing netfilter helpers outside of
services is therefore not needed anymore. For more information on
handling netfilter helpers in services, please have a look at
firewalld.zone(5).
removemodule
This option will result in a warning message and will be ignored.
Handling of netfilter helpers has been merged into services
completely. Adding or removing netfilter helpers outside of
services is therefore not needed anymore. For more information on
handling netfilter helpers in services, please have a look at
firewalld.zone(5).
remove-service=service
Remove a service from the default zone. This option can be
specified multiple times.
The service is one of the firewalld provided services. To get a
list of the supported services, use firewall-cmd get-services.
-s service, service=service
Add a service to the default zone. This option can be specified
multiple times.
The service is one of the firewalld provided services. To get a
list of the supported services, use firewall-cmd get-services.
-p portid[-portid]:protocol, port=portid[-portid]:protocol
Add the port to the default zone. This option can be specified
multiple times.
The port can either be a single port number or a port range
portid-portid. The protocol can either be tcp, udp, sctp or dccp.
-t interface, trust=interface
This option will result in a warning message.
Mark an interface as trusted. This option can be specified multiple
times. The interface will be bound to the trusted zone.
If the interface is used in a NetworkManager managed connection or
if there is an ifcfg file for this interface, the zone will be
changed to the zone defined in the configuration as soon as it gets
activated. To change the zone of a connection use
nm-connection-editor and set the zone to trusted, for an ifcfg
file, use an editor and add "ZONE=trusted". If the zone is not
defined in the ifcfg file, the firewalld default zone will be used.
-m interface, masq=interface
This option will result in a warning message.
Masquerading will be enabled in the default zone. The interface
argument will be ignored. This is for IPv4 only.
custom-rules=[type:][table:]filename
This option will result in a warning message and will be ignored.
Custom rule files are not supported by firewalld.
forward-port=if=interface:port=port:proto=protocol[:toport=destination
port:][:toaddr=destination address]
This option will result in a warning message.
Add the IPv4 forward port in the default zone. This option can be
specified multiple times.
The port can either be a single port number portid or a port range
portid-portid. The protocol can either be tcp, udp, sctp or dccp.
The destination address is an IP address.
block-icmp=icmptype
This option will result in a warning message.
Add an ICMP block for icmptype in the default zone. This option can
be specified multiple times.
The icmptype is the one of the icmp types firewalld supports. To
get a listing of supported icmp types: firewall-cmd get-icmptypes
Log Denied Options
get-log-denied
Print the log denied setting.
set-log-denied=value
Add logging rules right before reject and drop rules in the INPUT,
FORWARD and OUTPUT chains for the default rules and also final
reject and drop rules in zones for the configured link-layer packet
type. The possible values are: all, unicast, broadcast, multicast
and off. The default setting is off, which disables the logging.
This is a runtime and permanent change and will also reload the
firewall to be able to add the logging rules.
Automatic Helpers Options
get-automatic-helpers
Print the automatic helpers setting.
set-automatic-helpers=value
For the secure use of iptables and connection tracking helpers it
is recommended to turn AutomaticHelpers off. But this might have
side effects on other services using the netfilter helpers as the
sysctl setting in /proc/sys/net/netfilter/nfconntrackhelper will
be changed. With the system setting, the default value set in the
kernel or with sysctl will be used. Possible values are: yes, no
and system. The default value is system.
This is a runtime and permanent change and will also reload the
firewall to be able to make the helpers usable.
Zone Options
get-default-zone
Print default zone for connections and interfaces.
set-default-zone=zone
Set default zone for connections and interfaces where no zone has
been selected. Setting the default zone changes the zone for the
connections or interfaces, that are using the default zone.
get-zones
Print predefined zones as a space separated list.
get-services
Print predefined services as a space separated list.
get-icmptypes
Print predefined icmptypes as a space separated list.
get-zone-of-interface=interface
Print the name of the zone the interface is bound to or no zone.
get-zone-of-source=source[/mask]|MAC|ipset:ipset
Print the name of the zone the source is bound to or no zone.
info-zone=zone
Print information about the zone zone. The output format is:
zone
interfaces: interface1 ..
sources: source1 ..
services: service1 ..
ports: port1 ..
protocols: protocol1 ..
forward-ports:
forward-port1
..
source-ports: source-port1 ..
icmp-blocks: icmp-type1 ..
rich rules:
rich-rule1
..
list-all-zones
List everything added for or enabled in all zones. The output
format is:
zone1
interfaces: interface1 ..
sources: source1 ..
services: service1 ..
ports: port1 ..
protocols: protocol1 ..
forward-ports:
forward-port1
..
source-ports: source-port1 ..
icmp-blocks: icmp-type1 ..
rich rules:
rich-rule1
..
..
new-zone=zone
Add a new permanent zone.
new-zone-from-file=filename [name=zone]
Add a new permanent zone from a prepared zone file with an optional
name override.
path-zone=zone
Print path of the zone configuration file.
delete-zone=zone
Delete an existing permanent zone.
zone=zone set-description=description
Set new description to zone
zone=zone get-description
Print description for zone
zone=zone set-short=description
Set short description to zone
zone=zone get-short
Print short description for zone
zone=zone get-target
Get the target of a permanent zone.
zone=zone set-target=zone
Set the target of a permanent zone.
Options to Adapt and Query Zones
Options in this section affect only one particular zone. If used with
zone=zone option, they affect the zone zone. If the option is
omitted, they affect default zone (see get-default-zone).
[zone=zone] list-all
List everything added for or enabled in zone. If zone is omitted,
default zone will be used.
[zone=zone] list-services
List services added for zone as a space separated list. If zone is
omitted, default zone will be used.
[zone=zone] add-service=service
Add a service for zone. If zone is omitted, default zone will be
used. This option can be specified multiple times.
The service is one of the firewalld provided services. To get a
list of the supported services, use firewall-cmd get-services.
[zone=zone] remove-service-from-zone=service
Remove a service from zone. This option can be specified multiple
times. If zone is omitted, default zone will be used.
[zone=zone] query-service=service
Return whether service has been added for zone. If zone is omitted,
default zone will be used. Returns 0 if true, 1 otherwise.
[zone=zone] list-ports
List ports added for zone as a space separated list. A port is of
the form portid[-portid]/protocol, it can be either a port and
protocol pair or a port range with a protocol. If zone is omitted,
default zone will be used.
[zone=zone] add-port=portid[-portid]/protocol
Add the port for zone. If zone is omitted, default zone will be
used. This option can be specified multiple times.
The port can either be a single port number or a port range
portid-portid. The protocol can either be tcp, udp, sctp or dccp.
[zone=zone] remove-port=portid[-portid]/protocol
Remove the port from zone. If zone is omitted, default zone will be
used. This option can be specified multiple times.
[zone=zone] query-port=portid[-portid]/protocol
Return whether the port has been added for zone. If zone is
omitted, default zone will be used. Returns 0 if true, 1 otherwise.
[zone=zone] list-protocols
List protocols added for zone as a space separated list. If zone is
omitted, default zone will be used.
[zone=zone] add-protocol=protocol
Add the protocol for zone. If zone is omitted, default zone will be
used. This option can be specified multiple times. If a timeout is
supplied, the rule will be active for the specified amount of time
and will be removed automatically afterwards. timeval is either a
number (of seconds) or number followed by one of characters s
(seconds), m (minutes), h (hours), for example 20m or 1h.
The protocol can be any protocol supported by the system. Please
have a look at /etc/protocols for supported protocols.
[zone=zone] remove-protocol=protocol
Remove the protocol from zone. If zone is omitted, default zone
will be used. This option can be specified multiple times.
[zone=zone] query-protocol=protocol
Return whether the protocol has been added for zone. If zone is
omitted, default zone will be used. Returns 0 if true, 1 otherwise.
[zone=zone] list-icmp-blocks
List Internet Control Message Protocol (ICMP) type blocks added for
zone as a space separated list. If zone is omitted, default zone
will be used.
[zone=zone] add-icmp-block=icmptype
Add an ICMP block for icmptype for zone. If zone is omitted,
default zone will be used. This option can be specified multiple
times.
The icmptype is the one of the icmp types firewalld supports. To
get a listing of supported icmp types: firewall-cmd get-icmptypes
[zone=zone] remove-icmp-block=icmptype
Remove the ICMP block for icmptype from zone. If zone is omitted,
default zone will be used. This option can be specified multiple
times.
[zone=zone] query-icmp-block=icmptype
Return whether an ICMP block for icmptype has been added for zone.
If zone is omitted, default zone will be used. Returns 0 if true, 1
otherwise.
[zone=zone] list-forward-ports
List IPv4 forward ports added for zone as a space separated list.
If zone is omitted, default zone will be used.
For IPv6 forward ports, please use the rich language.
[zone=zone]
add-forward-port=port=portid[-portid]:proto=protocol[:toport=portid[-portid]][:toaddr=address[/mask]]
Add the IPv4 forward port for zone. If zone is omitted, default
zone will be used. This option can be specified multiple times.
The port can either be a single port number portid or a port range
portid-portid. The protocol can either be tcp, udp, sctp or dccp.
The destination address is a simple IP address.
For IPv6 forward ports, please use the rich language.
[zone=zone]
remove-forward-port=port=portid[-portid]:proto=protocol[:toport=portid[-portid]][:toaddr=address[/mask]]
Remove the IPv4 forward port from zone. If zone is omitted, default
zone will be used. This option can be specified multiple times.
For IPv6 forward ports, please use the rich language.
[zone=zone]
query-forward-port=port=portid[-portid]:proto=protocol[:toport=portid[-portid]][:toaddr=address[/mask]]
Return whether the IPv4 forward port has been added for zone. If
zone is omitted, default zone will be used. Returns 0 if true, 1
otherwise.
For IPv6 forward ports, please use the rich language.
[zone=zone] list-source-ports
List source ports added for zone as a space separated list. A port
is of the form portid[-portid]/protocol. If zone is omitted,
default zone will be used.
[zone=zone] add-source-port=portid[-portid]/protocol
Add the source port for zone. If zone is omitted, default zone will
be used. This option can be specified multiple times. If a timeout
is supplied, the rule will be active for the specified amount of
time and will be removed automatically afterwards.
The port can either be a single port number or a port range
portid-portid. The protocol can either be tcp, udp, sctp or dccp.
[zone=zone] remove-source-port=portid[-portid]/protocol
Remove the source port from zone. If zone is omitted, default zone
will be used. This option can be specified multiple times.
[zone=zone] query-source-port=portid[-portid]/protocol
Return whether the source port has been added for zone. If zone is
omitted, default zone will be used. Returns 0 if true, 1 otherwise.
[zone=zone] add-masquerade
Enable IPv4 masquerade for zone. If zone is omitted, default zone
will be used. Masquerading is useful if the machine is a router and
machines connected over an interface in another zone should be able
to use the first connection.
For IPv6 masquerading, please use the rich language.
[zone=zone] remove-masquerade
Disable IPv4 masquerade for zone. If zone is omitted, default zone
will be used.
For IPv6 masquerading, please use the rich language.
[zone=zone] query-masquerade
Return whether IPv4 masquerading has been enabled for zone. If zone
is omitted, default zone will be used. Returns 0 if true, 1
otherwise.
For IPv6 masquerading, please use the rich language.
[zone=zone] list-rich-rules
List rich language rules added for zone as a newline separated
list. If zone is omitted, default zone will be used.
[zone=zone] add-rich-rule='rule'
Add rich language rule 'rule' for zone. This option can be
specified multiple times. If zone is omitted, default zone will be
used.
For the rich language rule syntax, please have a look at
firewalld.richlanguage(5).
[zone=zone] remove-rich-rule='rule'
Remove rich language rule 'rule' from zone. This option can be
specified multiple times. If zone is omitted, default zone will be
used.
For the rich language rule syntax, please have a look at
firewalld.richlanguage(5).
[zone=zone] query-rich-rule='rule'
Return whether a rich language rule 'rule' has been added for zone.
If zone is omitted, default zone will be used. Returns 0 if true, 1
otherwise.
For the rich language rule syntax, please have a look at
firewalld.richlanguage(5).
Options to Handle Bindings of Interfaces
Binding an interface to a zone means that this zone settings are used
to restrict traffic via the interface.
Options in this section affect only one particular zone. If used with
zone=zone option, they affect the zone zone. If the option is
omitted, they affect default zone (see get-default-zone).
For a list of predefined zones use firewall-cmd get-zones.
An interface name is a string up to 16 characters long, that may not
contain ' ', '/', '!' and '*'.
[zone=zone] list-interfaces
List interfaces that are bound to zone zone as a space separated
list. If zone is omitted, default zone will be used.
[zone=zone] add-interface=interface
Bind interface interface to zone zone. If zone is omitted, default
zone will be used.
[zone=zone] change-interface=interface
Change zone the interface interface is bound to to zone zone. If
zone is omitted, default zone will be used. If old and new zone are
the same, the call will be ignored without an error. If the
interface has not been bound to a zone before, it will behave like
add-interface.
[zone=zone] query-interface=interface
Query whether interface interface is bound to zone zone. Returns 0
if true, 1 otherwise.
[zone=zone] remove-interface=interface
Remove binding of interface interface from zone zone. If zone is
omitted, default zone will be used.
Options to Handle Bindings of Sources
Binding a source to a zone means that this zone settings will be used
to restrict traffic from this source.
A source address or address range is either an IP address or a network
IP address with a mask for IPv4 or IPv6 or a MAC address or an ipset
with the ipset: prefix. For IPv4, the mask can be a network mask or a
plain number. For IPv6 the mask is a plain number. The use of host
names is not supported.
Options in this section affect only one particular zone. If used with
zone=zone option, they affect the zone zone. If the option is
omitted, they affect default zone (see get-default-zone).
For a list of predefined zones use firewall-cmd get-zones.
[zone=zone] list-sources
List sources that are bound to zone zone as a space separated list.
If zone is omitted, default zone will be used.
[zone=zone] add-source=source[/mask]|MAC|ipset:ipset
Bind the source to zone zone. If zone is omitted, default zone will
be used.
[zone=zone] change-source=source[/mask]|MAC|ipset:ipset
Change zone the source is bound to to zone zone. If zone is
omitted, default zone will be used. If old and new zone are the
same, the call will be ignored without an error. If the source has
not been bound to a zone before, it will behave like add-source.
[zone=zone] query-source=source[/mask]|MAC|ipset:ipset
Query whether the source is bound to the zone zone. Returns 0 if
true, 1 otherwise.
[zone=zone] remove-source=source[/mask]|MAC|ipset:ipset
Remove binding of the source from zone zone. If zone is omitted,
default zone will be used.
IPSet Options
new-ipset=ipset type=ipset type [option=ipset option[=value]]
Add a new permanent ipset with specifying the type and optional
options.
new-ipset-from-file=filename [name=ipset]
Add a new permanent ipset from a prepared ipset file with an
optional name override.
delete-ipset=ipset
Delete an existing permanent ipset.
info-ipset=ipset
Print information about the ipset ipset. The output format is:
ipset
type: type
options: option1[=value1] ..
entries: entry1 ..
get-ipsets
Print predefined ipsets as a space separated list.
ipset=ipset add-entry=entry
Add a new entry to the ipset.
ipset=ipset remove-entry=entry
Remove an entry from the ipset.
ipset=ipset query-entry=entry
Return whether the entry has been added to an ipset. Returns 0 if
true, 1 otherwise.
ipset=ipset get-entries
List all entries of the ipset.
ipset=ipset add-entries-from-file=filename
Add a new entries to the ipset from the file. For all entries that
are listed in the file but already in the ipset, a warning will be
printed.
The file should contain an entry per line. Lines starting with an
hash or semicolon are ignored. Also empty lines.
ipset=ipset remove-entries-from-file=filename
Remove existing entries from the ipset from the file. For all
entries that are listed in the file but not in the ipset, a warning
will be printed.
The file should contain an entry per line. Lines starting with an
hash or semicolon are ignored. Also empty lines.
ipset=ipset set-description=description
Set new description to ipset
ipset=ipset get-description
Print description for ipset
ipset=ipset set-short=description
Set new short description to ipset
ipset=ipset get-short
Print short description for ipset
path-ipset=ipset
Print path of the ipset configuration file.
Service Options
info-service=service
Print information about the service service. The output format is:
service
ports: port1 ..
protocols: protocol1 ..
source-ports: source-port1 ..
modules: module1 ..
destination: ipv1:address1 ..
new-service=service
Add a new permanent service.
new-service-from-file=filename [name=service]
Add a new permanent service from a prepared service file with an
optional name override.
delete-service=service
Delete an existing permanent service.
path-service=service
Print path of the service configuration file.
service=service set-description=description
Set new description to service
service=service get-description
Print description for service
service=service set-short=description
Set short description to service
service=service get-short
Print short description for service
service=service add-port=portid[-portid]/protocol
Add a new port to the permanent service.
service=service remove-port=portid[-portid]/protocol
Remove a port from the permanent service.
service=service query-port=portid[-portid]/protocol
Return wether the port has been added to the permanent service.
service=service get-ports
List ports added to the permanent service.
service=service add-protocol=protocol
Add a new protocol to the permanent service.
service=service remove-protocol=protocol
Remove a protocol from the permanent service.
service=service query-protocol=protocol
Return wether the protocol has been added to the permanent service.
service=service get-protocols
List protocols added to the permanent service.
service=service add-source-port=portid[-portid]/protocol
Add a new source port to the permanent service.
service=service remove-source-port=portid[-portid]/protocol
Remove a source port from the permanent service.
service=service query-source-port=portid[-portid]/protocol
Return wether the source port has been added to the permanent
service.
service=service get-source-ports
List source ports added to the permanent service.
service=service add-module=module
Add a new module to the permanent service.
service=service remove-module=module
Remove a module from the permanent service.
service=service query-module=module
Return wether the module has been added to the permanent service.
service=service get-modules
List modules added to the permanent service.
service=service set-destination=ipv:address[/mask]
Set destination for ipv to address[/mask] in the permanent service.
service=service remove-destination=ipv
Remove the destination for ipv from the permanent service.
service=service query-destination=ipv:address[/mask]
Return wether the destination ipv to address[/mask] has been set in
the permanent service.
service=service get-destinations
List destinations added to the permanent service.
Helper Options
Options in this section affect only one particular helper.
info-helper=helper
Print information about the helper helper. The output format is:
helper
family: family
module: module
ports: port1 ..
The following options are only usable in the permanent configuration.
new-helper=helper module=nfconntrackmodule [family=ipv4|ipv6]
Add a new permanent helper with module and optionally family
defined.
new-helper-from-file=filename [name=helper]
Add a new permanent helper from a prepared helper file with an
optional name override.
delete-helper=helper
Delete an existing permanent helper.
load-helper-defaults=helper
Load helper default settings or report NODEFAULTS error.
path-helper=helper
Print path of the helper configuration file.
get-helpers
Print predefined helpers as a space separated list.
helper=helper set-description=description
Set new description to helper
helper=helper get-description
Print description for helper
helper=helper set-short=description
Set short description to helper
helper=helper get-short
Print short description for helper
helper=helper add-port=portid[-portid]/protocol
Add a new port to the permanent helper.
helper=helper remove-port=portid[-portid]/protocol
Remove a port from the permanent helper.
helper=helper query-port=portid[-portid]/protocol
Return wether the port has been added to the permanent helper.
helper=helper get-ports
List ports added to the permanent helper.
helper=helper set-module=description
Set module description for helper
helper=helper get-module
Print module description for helper
helper=helper set-family=description
Set family description for helper
helper=helper get-family
Print family description of helper
Internet Control Message Protocol (ICMP) type Options
info-icmptype=icmptype
Print information about the icmptype icmptype. The output format
is:
icmptype
destination: ipv1 ..
new-icmptype=icmptype
Add a new permanent icmptype.
new-icmptype-from-file=filename [name=icmptype]
Add a new permanent icmptype from a prepared icmptype file with an
optional name override.
delete-icmptype=icmptype
Delete an existing permanent icmptype.
icmptype=icmptype set-description=description
Set new description to icmptype
icmptype=icmptype get-description
Print description for icmptype
icmptype=icmptype set-short=description
Set short description to icmptype
icmptype=icmptype get-short
Print short description for icmptype
icmptype=icmptype add-destination=ipv
Enable destination for ipv in permanent icmptype. ipv is one of
ipv4 or ipv6.
icmptype=icmptype remove-destination=ipv
Disable destination for ipv in permanent icmptype. ipv is one of
ipv4 or ipv6.
icmptype=icmptype query-destination=ipv
Return whether destination for ipv is enabled in permanent
icmptype. ipv is one of ipv4 or ipv6.
icmptype=icmptype get-destinations
List destinations in permanent icmptype.
path-icmptype=icmptype
Print path of the icmptype configuration file.
Direct Options
The direct options give a more direct access to the firewall. These
options require user to know basic iptables concepts, i.e. table
(filter/mangle/nat/...), chain (INPUT/OUTPUT/FORWARD/...), commands
(-A/-D/-I/...), parameters (-p/-s/-d/-j/...) and targets
(ACCEPT/DROP/REJECT/...).
Direct options should be used only as a last resort when it's not
possible to use for example add-service=service or
add-rich-rule='rule'.
The first argument of each option has to be ipv4 or ipv6 or eb. With
ipv4 it will be for IPv4 (iptables(8)), with ipv6 for IPv6
(ip6tables(8)) and with eb for ethernet bridges (ebtables(8)).
direct get-all-chains
Get all chains added to all tables.
This option concerns only chains previously added with direct
add-chain.
direct get-chains { ipv4 | ipv6 | eb } table
Get all chains added to table table as a space separated list.
This option concerns only chains previously added with direct
add-chain.
direct add-chain { ipv4 | ipv6 | eb } table chain
Add a new chain with name chain to table table.
There already exist basic chains to use with direct options, for
example INPUTdirect chain (see iptables-save | grep direct output
for all of them). These chains are jumped into before chains for
zones, i.e. every rule put into INPUTdirect will be checked before
rules in zones.
direct remove-chain { ipv4 | ipv6 | eb } table chain
Remove the chain with name chain from table table.
direct query-chain { ipv4 | ipv6 | eb } table chain
Return whether a chain with name chain exists in table table.
Returns 0 if true, 1 otherwise.
This option concerns only chains previously added with direct
add-chain.
direct get-all-rules
Get all rules added to all chains in all tables as a newline
separated list of the priority and arguments.
direct get-rules { ipv4 | ipv6 | eb } table chain
Get all rules added to chain chain in table table as a newline
separated list of the priority and arguments.
direct add-rule { ipv4 | ipv6 | eb } table chain priority args
Add a rule with the arguments args to chain chain in table table
with priority priority.
The priority is used to order rules. Priority 0 means add rule on
top of the chain, with a higher priority the rule will be added
further down. Rules with the same priority are on the same level
and the order of these rules is not fixed and may change. If you
want to make sure that a rule will be added after another one, use
a low priority for the first and a higher for the following.
direct remove-rule { ipv4 | ipv6 | eb } table chain priority args
Remove a rule with priority and the arguments args from chain chain
in table table.
direct remove-rules { ipv4 | ipv6 | eb } table chain
Remove all rules in the chain with name chain exists in table
table.
This option concerns only rules previously added with direct
add-rule in this chain.
direct query-rule { ipv4 | ipv6 | eb } table chain priority args
Return whether a rule with priority and the arguments args exists
in chain chain in table table. Returns 0 if true, 1 otherwise.
direct get-all-passthroughs
Get all permanent passthrough as a newline separated list of the
ipv value and arguments.
direct get-passthroughs { ipv4 | ipv6 | eb }
Get all permanent passthrough rules for the ipv value as a newline
separated list of the priority and arguments.
direct add-passthrough { ipv4 | ipv6 | eb } args
Add a permanent passthrough rule with the arguments args for the
ipv value.
direct remove-passthrough { ipv4 | ipv6 | eb } args
Remove a permanent passthrough rule with the arguments args for the
ipv value.
direct query-passthrough { ipv4 | ipv6 | eb } args
Return whether a permanent passthrough rule with the arguments args
exists for the ipv value. Returns 0 if true, 1 otherwise.
Lockdown Options
Local applications or services are able to change the firewall
configuration if they are running as root (example: libvirt) or are
authenticated using PolicyKit. With this feature administrators can
lock the firewall configuration so that only applications on lockdown
whitelist are able to request firewall changes.
The lockdown access check limits D-Bus methods that are changing
firewall rules. Query, list and get methods are not limited.
The lockdown feature is a very light version of user and application
policies for firewalld and is turned off by default.
lockdown-on
Enable lockdown. Be careful - if firewall-cmd is not on lockdown
whitelist when you enable lockdown you won't be able to disable it
again with firewall-cmd, you would need to edit firewalld.conf.
lockdown-off
Disable lockdown.
query-lockdown
Query whether lockdown is enabled. Returns 0 if lockdown is
enabled, 1 otherwise.
Lockdown Whitelist Options
The lockdown whitelist can contain commands, contexts, users and user
ids.
If a command entry on the whitelist ends with an asterisk '*', then all
command lines starting with the command will match. If the '*' is not
there the absolute command inclusive arguments must match.
Commands for user root and others is not always the same. Example: As
root /bin/firewall-cmd is used, as a normal user /usr/bin/firewall-cmd
is be used on Fedora.
The context is the security (SELinux) context of a running application
or service. To get the context of a running application use ps -e
context.
Warning: If the context is unconfined, then this will open access for
more than the desired application.
The lockdown whitelist entries are checked in the following order:
1. context
2. uid
3. user
4. command
list-lockdown-whitelist-commands
List all command lines that are on the whitelist.
add-lockdown-whitelist-command=command
Add the command to the whitelist.
remove-lockdown-whitelist-command=command
Remove the command from the whitelist.
query-lockdown-whitelist-command=command
Query whether the command is on the whitelist. Returns 0 if true, 1
otherwise.
list-lockdown-whitelist-contexts
List all contexts that are on the whitelist.
add-lockdown-whitelist-context=context
Add the context context to the whitelist.
remove-lockdown-whitelist-context=context
Remove the context from the whitelist.
query-lockdown-whitelist-context=context
Query whether the context is on the whitelist. Returns 0 if true, 1
otherwise.
list-lockdown-whitelist-uids
List all user ids that are on the whitelist.
add-lockdown-whitelist-uid=uid
Add the user id uid to the whitelist.
remove-lockdown-whitelist-uid=uid
Remove the user id uid from the whitelist.
query-lockdown-whitelist-uid=uid
Query whether the user id uid is on the whitelist. Returns 0 if
true, 1 otherwise.
list-lockdown-whitelist-users
List all user names that are on the whitelist.
add-lockdown-whitelist-user=user
Add the user name user to the whitelist.
remove-lockdown-whitelist-user=user
Remove the user name user from the whitelist.
query-lockdown-whitelist-user=user
Query whether the user name user is on the whitelist. Returns 0 if
true, 1 otherwise.
Policy Options
policy-server
Change Polkit actions to 'server' (more restricted)
policy-desktop
Change Polkit actions to 'desktop' (less restricted)
SEE ALSO
firewall-applet(1), firewalld(1), firewall-cmd(1), firewall-config(1),
firewalld.conf(5), firewalld.direct(5), firewalld.dbus(5),
firewalld.icmptype(5), firewalld.lockdown-whitelist(5), firewall-
offline-cmd(1), firewalld.richlanguage(5), firewalld.service(5),
firewalld.zone(5), firewalld.zones(5), firewalld.ipset(5),
firewalld.helper(5)
NOTES
firewalld home page:
http://www.firewalld.org
More documentation with examples:
http://fedoraproject.org/wiki/FirewallD
AUTHORS
Thomas Woerner
Developer
Jiri Popelka
Developer
firewalld 0.5.3 FIREWALL-OFFLINE-C(1)